收藏本站
OPERATION
‘Full’ sample rate (up to 3200Hz)
‘Full’ leaves the accelerometer in active mode and the
Flash memory powered, and uses the same sample
rate as the actual recording. This mode consumes
more power (~300uA @ 3200Hz), but will trigger
even on brief G-level exceedances. In addition, this
mode will record the 32 pre-trigger samples leading up
to the trigger event. This is the recommended mode of
operation for recording impacts and other transient
events.
Note that in either mode, a button press is still required
to arm the G-level trigger between recordings. The G-
level trigger will arm approximately 1 second after
pressing the button (plus any user-set time delays) to
prevent nuisance triggering due to the button recoil. To
minimize nuisance triggers, avoid setting a trigger level
at or near the noise floor (0.1 ~ 0.2g). For DC
triggering, the contribution of gravity (up to 1G +/- any
offset error), if any, must be added to this value.
To Erase data the device
DO NOT DELETE FILES FROM THE Slam Stick?!!! To
erase data (the configuration file will not be erased),
hold down the white button while unplugging the USB
connection. Keep the white button pressed down until
the orange LED starts flashing. At this point you can
remove pressure from the button. The device is done
erasing when the flashing LED stops. This will clear any
previous recordings from the device so it will be ready
for more testing.
To Install on Your Vibration Structure
Attach the Slam Stick? to the vibration source using
any means that will ensure a high quality vibration
energy transfer with minimal damping. Ensure that the
mounting method also allows for easy removal of the
Slam Stick? after the test. Ensure that the user still
has access to the operating button after installation, or
delay is long enough to permit installation. Ensure that
the axes orientation of the Slam Stick? is suitable for
the desired measurement (see figure below). It is
suggested to take a picture of the device for later
confirmation of mounting position. Suggested
mounting options include bee’s wax, thin double sided
tape, duct tape and/or mechanical brackets. If
mechanical brackets are used be careful not to over
load the plastic enclosure. Please note that the
enclosure is only dust proof and should not be
submerged or subjected to any direct fluid spray.
To Record
To begin the vibration measurement press and release
the white button on the Slam Stick?. An amber LED
near the rear end of the device will indicate the
recording progress. If a pre-recording delay has been
set, the LED will flash briefly, about every 2 seconds,
during the delay period. During active recording, the
LED will blink rapidly, then stop when the recording
completes.
During recording, the button can also be pressed
during the delay period (if any) to skip the delay and
begin recording, or during the active recording period
to terminate the recording early.
REVISION N0. 001
REVISION DATE: 08-24-2010
www.mide.com
5
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
VSLY3850 IR EMITTER 850NM HIGH SPEED
VSLY5850 IR EMITTER 850NM HIGH SPEED DIP
VSMY2850G IR EMITTER 850NM HIGH SPEED SMD
VSMY7850X01-GS08 IR EMITTER 850NM HIGH SPEED SMD
VSOP38336 IC SIGNAL CONDITIONING 36KHZ QFN
WALLS-C4600-001 SYNJETWIRE HARNESS 4WIRE 600MM
WIT2410SDK DEVELOPMENT KIT, 2 WIT2410M MODU
WIT2411DK DEVELOPMENT KIT, 2 WIT2411M MODU
相关代理商/技术参数
VR02GC223MAA 制造商:AVX 功能描述:RMX322X2000 '93 .4LS S5J1C
VR05-1516LB 功能描述:CONV DC/DC 15V OUT 167MA 5W RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:VR-LB 标准包装:15 系列:Econoline REC3-DR 类型:隔离 输出数:2 电压 - 输入（最小）:4.5V 电压 - 输入（最大）:5.5V Voltage - Output 1:5V Voltage - Output 2:-5V Voltage - Output 3:- 电流 - 输出（最大）:300mA，300mA 电源（瓦） - 制造商系列:3W 电压 - 隔离:1kV（1000V） 特点:- 安装类型:表面贴装 封装/外壳:24-DIP SMD 模块（18 引线） 尺寸/尺寸:1.26" L x 0.80" W x 0.44" H（32.0mm x 20.3mm x 11.2mm） 包装:管件 工作温度:-40°C ~ 80°C 效率:75% 电源（瓦特）- 最大:3W 其它名称:10005457
VR05-FW 制造商:Custom Connector Corporation 功能描述:
VR05-LFW 制造商:Custom Connector Corporation 功能描述:Socket, Relay, Automotive Relay, 5 Pin Automotive, Crimp, Thermoplastic
VR05-PCB 制造商:Custom Connector Corporation 功能描述:Socket, Relay, Automotive Relay, 5 Pin Automotive, PC Board, Thermoplastic 制造商:Song Chuan Precision Company 功能描述:VR Series 5 Pin Socket PCB Micro Automotive Relay
VR05-SPCB 制造商:Custom Connector Corporation 功能描述:Automotive Relay Sockets 5 Pin
VR091B080CL 功能描述:DC/DC转换器 VRM 9.1 80A 12V to 1.10-1.85V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
VR091B080CS 功能描述:DC/DC转换器 148W 12V/1.075-1.85V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: